联系我们
公司名称：XXX
电话：XXX
手机：XXX
联系人：XXX
地址：XXX
新闻动态
超级脱模剂核心母料特点
一、 特别功能
I. Special Functions
1、能在几秒钟内将废机油、机油、润滑油等工业油脂与水溶为一体。
1. Waste oil, oil, lubricating oil and other industrial oils can be integrated with water in a few seconds.
2、不含有毒溶剂、碱性、环保、耐碱、耐硬水。
2. It does not contain toxic solvents, alkalinity, environmental protection, alkali resistance and hard water.
二、 生产配比：
2. Production Ratio:
废机油10%+超级脱模剂核心母料2%+水88%+速溶耐酸碱透明增稠粉500克+拉丝粉80克+色素1克+防腐剂、香精适量=脱模剂，自己可以根据成本和品质的需要调整比例。
Waste oil 10%+ super release agent, core material 2%+ water 88%+ instant acid alkali and transparent thickening powder 500 grams + drawing powder 80 grams + pigment 1 grams + preservative, essence amount = release agent, you can adjust the proportion according to the needs of cost and quality.
三、 生产流程：
3. Production process:
先将防腐剂加入水中搅拌,然后将超级脱模剂核心母料加入水中搅拌，浸泡一小时后再搅拌均匀，确保完全溶解后再将废机油、香精色素加入水中搅拌，最后将速溶耐酸碱透明增稠粉、拉丝粉加入水中搅拌,过半小时左右稠了后搅拌均勺就行了。
First, the preservative is added to the water to stir, then the core masterbatch of super demoulding agent is added to the water and stirred in water. After soaking for an hour, the mixture is stirred evenly, and then the waste oil and the essence pigment are added into the water to stir in the water. Finally, the instant acid alkali transparent thickening powder and the drawing powder are added into the water and stirred in the water. After half hour thick, the stirring spoon will be done.
I. Special Functions
1、能在几秒钟内将废机油、机油、润滑油等工业油脂与水溶为一体。
1. Waste oil, oil, lubricating oil and other industrial oils can be integrated with water in a few seconds.
2、不含有毒溶剂、碱性、环保、耐碱、耐硬水。
2. It does not contain toxic solvents, alkalinity, environmental protection, alkali resistance and hard water.
二、 生产配比：
2. Production Ratio:
废机油10%+超级脱模剂核心母料2%+水88%+速溶耐酸碱透明增稠粉500克+拉丝粉80克+色素1克+防腐剂、香精适量=脱模剂，自己可以根据成本和品质的需要调整比例。
Waste oil 10%+ super release agent, core material 2%+ water 88%+ instant acid alkali and transparent thickening powder 500 grams + drawing powder 80 grams + pigment 1 grams + preservative, essence amount = release agent, you can adjust the proportion according to the needs of cost and quality.
三、 生产流程：
3. Production process:
先将防腐剂加入水中搅拌,然后将超级脱模剂核心母料加入水中搅拌，浸泡一小时后再搅拌均匀，确保完全溶解后再将废机油、香精色素加入水中搅拌，最后将速溶耐酸碱透明增稠粉、拉丝粉加入水中搅拌,过半小时左右稠了后搅拌均勺就行了。
First, the preservative is added to the water to stir, then the core masterbatch of super demoulding agent is added to the water and stirred in water. After soaking for an hour, the mixture is stirred evenly, and then the waste oil and the essence pigment are added into the water to stir in the water. Finally, the instant acid alkali transparent thickening powder and the drawing powder are added into the water and stirred in the water. After half hour thick, the stirring spoon will be done.
